AC repair
Furnace & heating
Heat pumps
Ductless mini splits
Carrier
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateStyles & brands we work with
- AC repair
- Furnace & heating
- Heat pumps
- Ductless mini splits
- Carrier
- Trane
- Goodman
See the difference
Before
After
Before
After
Before
AfterHow Much Does Heat Pump Installation Cost in Irving?
Heat pump installation in Irving typically runs between $3,500 and $7,500 as a typical estimated range, with most single-system residential replacements landing in the middle of that band. The figure covers removal of the old equipment, the new heat pump, and the labor to set and start it. What moves you up or down depends mostly on tonnage, duct condition, and whether you’re adding refrigerant lines or reusing what’s there. The written estimate always sets the final price.
We’re Kingsley AC Repair, and heat pumps are cooling and heating under one machine, which is exactly the kind of work we do year-round. Every job is held to the Kingsley standard, and every estimate is free. Call (855) 473-9031. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- Typical estimated range for heat pump installation in Irving: $3,500 – $7,500 per system.
- Equipment brand, tonnage, and ductwork condition drive most of the variance.
- We service nine major manufacturers – Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard – so your new system is likely one we already know well.
- The estimate is free and the price is set per job by the written estimate.
Heat Pump Installation Cost Breakdown (2026)
Here’s how the money typically splits on a residential heat pump install in Irving. These are estimated ranges for a standard single-family home; the written estimate confirms exact numbers after we see the equipment and the space.
| Line item | Typical estimated range |
|---|---|
| Full system replacement (heat pump, air handler, thermostat) | $3,500 – $7,500 |
| Same-tier equipment swap, ductwork reused | Lower end of the range |
| Higher-capacity or two-stage/communicating equipment | Upper end of the range |
| Duct modifications or added refrigerant line runs | Priced into the written estimate |
| AC installation (cooling-only, for comparison) | $3,500 – $7,500 |
| AC repair | $150 – $650 |
| Furnace repair | $150 – $700 |
| Tune-up | $80 – $200 |
What pushes the number up: a jump in tonnage because the old system was undersized for the square footage, ductwork that needs sealing or resizing, a switch to a different equipment tier, or long line runs to a new indoor location. What pulls it down: reusing serviceable ductwork, staying with the same tonnage and equipment tier, and choosing a system we already service regularly. We don’t pad the estimate to hit a quota. Brand-neutral diagnostics mean the recommendation follows the condition of the system and your situation.
What Affects Heat Pump Installation Pricing in Irving
Heat pumps in North Texas work harder on the cooling side than buyers from colder markets expect. A heat pump sized for a mild climate will run itself ragged through an Irving summer, and a system that’s undersized is a system that fails early. Here are the factors that move the estimate.
- Tonnage and load calculation. A proper install starts with a load calculation based on your square footage, window exposure, and insulation – not a guess. Oversized equipment short-cycles; undersized equipment never catches up. Both cost more over time than the right size.
- Equipment tier and brand. Single-stage, two-stage, and variable-speed systems sit at different price points. Because we’re factory-familiar with nine major brands, we can recommend the tier that fits your house rather than the one with the best margin.
- Ductwork condition. Reusing existing ducts keeps cost down, but leaky or undersized ducts in an older Irving home can sabotage a new system. Sealing or modifying ductwork is priced into the written estimate when it’s needed.
- Refrigerant line and electrical work. Some replacements reuse the existing lines and disconnect. Others need new line runs or an electrical upgrade. Both affect the total.
- Indoor unit location and access. A closet-installed air handler, an attic mount, or a tight mechanical space adds labor time. Straightforward access keeps the install on the lower end.
- Thermostat and controls. A basic thermostat versus a communicating or smart control changes the number modestly, and the right control can help a heat pump run more efficiently.
One more factor that doesn’t show up in the line items: the mild Irving winters mean a heat pump does double duty as your heating system. That’s the whole point of a heat pump – one machine for both seasons. If you’re also weighing a separate furnace, our Irving service area page walks through how heating and cooling fit together for local homeowners.
How to Save on Heat Pump Installation
You can’t shrink the equipment cost much, but you can keep the job from climbing into the top of the range. These are the levers that actually matter.
- Get the load calculation, not a rule of thumb. Matching tonnage to your house prevents the oversized-system mistake. It also prevents a second install down the road.
- Keep your ductwork if it’s sound. Reusing ducts that pass inspection saves real money. If a technician tells you to replace ducts without walking you through why, ask for the reason.
- Compare tiers on paper. Ask what a two-stage or variable-speed system costs versus single-stage, and what the difference means in your daily use. Then decide.
- Handle the cooling side first if the old system still works. If the heat pump is limping but serviceable, a repair now can buy time to plan the install without urgency. Our AC repair work runs a typical $150 – $650, which is far less than an unplanned replacement.
- Keep up with tune-ups. A tune-up at a typical $80 – $200 keeps a working system running and catches small problems before they become install conversations.
- Plan the install instead of reacting to it. A planned install lets you shop the equipment tier and schedule around the work. A failed system in July forces the decision on the equipment’s terms.
The estimate is free, and the price is set per job by the written estimate. No guesswork, no pressure. Call (855) 473-9031. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Heat Pump vs. Separate AC and Furnace: What’s the Better Buy in Irving?
A heat pump covers both cooling and heating in one unit, so a single install replaces what would otherwise be an AC plus a furnace. For many Irving homes that means one piece of equipment to maintain, one set of filters, and one system to repair when something goes wrong. The trade-off: heat pumps lose efficiency in deep cold, which almost never shows up in this climate. Our furnace repair work runs a typical $150 – $700, and homeowners still keeping a gas furnace have that option. If you’re replacing both an aging AC and an aging furnace at once, a heat pump can simplify the whole picture. If your furnace is newer and healthy, a straight AC installation (typical $3,500 – $7,500) may be the smarter call. We’ll tell you which one fits your house.
What Happens When You Call
You call (855) 473-9031 and talk to someone who understands the equipment. We answer 24/7, and we dispatch technicians Sunday through Friday, 7am to 7pm. We’re closed on Saturday. From there it’s straightforward: we look at your current system, confirm the tonnage and duct condition, and put an estimate in writing. You’ll know the line items before anyone touches the equipment, and the written estimate sets the final price. You shouldn’t have to explain your equipment to your technician – we know these brands, and we’ll confirm what you have before we quote. If we’re visiting for a heat pump install and your furnace is also on its last legs, we can cover that on the same trip. Heating and cooling, handled.
Why Choose a Specialist for Your Heat Pump Installation
Kingsley AC Repair is an HVAC specialist, not a general contractor. We do three things: AC repair, AC installation, and furnace repair. That’s it. Every technician we send is an HVAC professional, not a multi-trade generalist learning HVAC between other jobs. Twelve years in, nine brands. One standard. When we recommend a repair or a replacement, the recommendation follows the condition of your system and your situation – not an equipment quota. That matters most on installs, where the wrong recommendation costs more than any repair. We’ve been serving Irving since 2014, and the same standard that earns an AC repair call carries forward when the heating season arrives.
FAQs – Heat Pump Installation Cost
How much does heat pump installation cost in Irving?
Typical estimated ranges in Irving run $3,500 – $7,500 for a full residential heat pump installation. The written estimate sets the final price after we see your equipment, ductwork, and home. Call (855) 473-9031 for a free estimate.
Is it cheaper to repair or replace my heat pump?
It depends on the system’s age and the cost of the repair. A repair at a typical $150 – $650 is far less than a replacement, but if the compressor or reversing valve is failing, replacement often wins. Brand-neutral diagnostics tell you which way it tilts. Call (855) 473-9031 and we’ll give you a straight answer.
Can you install a heat pump the same day?
Same-day installation is possible when the equipment is on hand and the job is straightforward. Most installs are booked ahead so the equipment and crew match your schedule. Call (855) 473-9031. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Do you service my brand of heat pump?
Almost certainly. We’re trained and equipped to service Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. If your new system is one of these, we already know it. Call (855) 473-9031 to confirm your model.
Will a heat pump cover my heating in Irving winters?
Yes. Irving’s mild winters suit a heat pump well, and a properly sized system handles heating and cooling in one unit. Deep-cold efficiency loss is a cold-climate concern that rarely applies here. The right tonnage is what matters. Call (855) 473-9031 for an estimate sized to your home.
What’s the difference between a heat pump install and an AC install?
A heat pump replaces both a cooling and a heating system; an AC install covers cooling only and leaves your furnace in place. AC installation runs a typical $3,500 – $7,500, similar to a heat pump. Which makes sense depends on your furnace’s condition. Call (855) 473-9031 and we’ll walk through both.
Get a Free Heat Pump Installation Estimate in Irving
If you’re weighing a heat pump against a straight AC replacement, the fastest way to get a real number is a free estimate. Call (855) 473-9031. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We’re closed Saturday. We’ll confirm your equipment, size the job to your home, and put it in writing. Kingsley AC Repair has served Irving since 2014, and every install is held to the same named standard. Nine brands. One standard. Heating and cooling, handled.
Written by the team at Kingsley AC Repair, serving Irving since 2014.
Pricing reflects the Irving market as of 2026. Kingsley AC Repair offers free estimates – call (855) 473-9031.
What Our Customers Say
"Work was done properly. I did have to follow up twice to get the invoice and the warranty info emailed over. The repair itself has been trouble free."
- Carlos Hernandez"Drain line was clogged and the safety switch had shut the whole system down. Cleared it, flushed it, and installed a proper cleanout so I can pour vinegar through it myself once a season."
- Robert Pruitt"New system install, two days, and they were careful with the floors and the attic access the entire time. Registered the warranty for me and emailed the paperwork."
- Shane Quinn